OEM Integration DSP with Automatic Time Correction and Digital EQ. 8-ch. Inputs / 4-ch. Stereo + 2 Subwoofer RCA Outputs
The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units, while retaining OEM fader control.
Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed.
With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs.
By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine tune the output signals.
Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS).
Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment.
An optional DRC-100 or DRC-200 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat.
Achieving great sound from your factory stereo has never been easier, or sounded better... Now with fader retention and subwoofer output!
Download and test-drive all TüN™ software versions in simulation mode for free (no FiX hardware needed).
Power Supply Type | Regulated DC-DC SMPS |
Input Operating Voltage | 10 - 16 VDC |
Standby Current Draw | <1.5 mA |
Operating Current Draw | 0.7 A |
Recommended Fuse Value | 1 A |
Input Channels | Eight |
Input Type | Differential-Balanced |
Input Voltage Range | 250 mV - 30 V RMS |
Minimum Input Voltage | 10 mV RMS |
Input Level Setting | Fully automatic |
Output Channels | Six (Front/Rear/Sub Output Pairs) |
Analog Output | Unbalanced, stereo RCA jacks |
Digital Output | N/A |
Output Impedance | 450 Ω |
S/N Ratio | 96 dB (A-Weighted, referred to 4V RMS Output) |
THD+N @ Rated Output | 0.02% (20 Hz - 20 kHz) |
Audio Resolution | 24 bit / 48 kHz |
Number of EQ Bands | 30 x 2 channels |
EQ Resolution | 1/3 octave (25 Hz - 20 kHz) |
Remote Level Control | Optional (DRC-100 or DRC-200) |
Remote Level Functions | Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-200 adds Subwoofer Level Control) |
Height (H) | 1.85 in / 47 mm |
Width (W) | 4.29 in / 109 mm |
Depth (D) | 6.14 in / 156 mm |
Net Weight | 2.58 lb / 1.17 kg |
JLid™
Summary:
JLid™ is JL Audio's protocol for digital controllers and for communication of settings between devices (not for audio signals).
Detailed Information:
JLid™ offers two-way communication for a range of accessories, including the following:
Wired System Controllers: DRC-100, DRC-200, DRC-205
Bluetooth® Communicator: VXi-BTC
Networking Accessory: VXi-HUB
JL Audio FiX™ and TwK™ processors each feature one “JLid™ Port”, designed for connection of a wired controller.
JL Audio VXi amplifiers offer powerful networking capabilities via JLid™, to deliver single-point control of multiple amplifiers in a system. This allows the user to adjust levels (Volume, Fader, Balance, Zone Level) and to select from multiple DSP presets, across an entire group of networked amplifiers. JL Audio VXi amplifiers each feature separate “JLid™ Control” and “JLid™ Comm” ports. Please refer to the VXi product manual and our Help Center for details.
JLid™ connections are made via standard CAT-5e cables.
Find the answers to many common questions:
Download: Firmware Updates to connect with TüN™ 2.0
Help Center Articles: FiX OEM Integration Processors
*********************************
U.S.A. Warranty Information - Mobile Audio Amplifiers and Electronic Products
JL Audio Amplifiers and Electronics are warrantied against defects in materials and workmanship for Two (2) Years from purchase date. The Mobile Audio Amplifier warranty can be expanded to a total of Three (3) Years from the date of purchase with the accompanying purchase of a qualifying JL Audio Amplifier Power Connection System and with installation by a JL Audio Authorized Retailer. JL Audio will, at its discretion, repair or replace any products that exhibit defects in materials and/or workmanship during the warranty period.
Please hold on to your sales receipt! All warranty service requires original sales receipt documentation. The warranty only applies to the original purchaser from an authorized retailer.
Note: Products purchased from unauthorized dealers are not covered under warranty.
Warranty Limitations
The following is not covered under JL Audio's warranty program:
1. Product with defaced, altered or removed serial numbers (no valid, legible serial number = no warranty).
2. Product owned by anyone other than the original purchaser from an authorized JL Audio dealer. (The warranty is not transferable and will not apply to products purchased from unauthorized dealers.)
3. Product that has been physically abused (run over by a car or beat with a hammer, for example).
4. Product that has not been installed according to the instructions in the owner's manual
5. Product in which repair and/or modification has been attempted by unauthorized parties
6. Product damaged cosmetically due to improper handling or normal wear and tear
7. Product damaged in an accident, due to criminal activity (attempted theft, gunshot damage, etc.) or by 'acts of God' (flooding, lightning, locusts, etc.)
8. Custom finishes or other cosmetic treatments applied to products. (JL Audio will not be responsible for restoring or maintaining any custom finishes)
9. Installation and shipping costs associated with removing, re-installing or shipping the product to JL Audio for warranty service
Ask your dealer for details on warranty limitations.
If you need Service on your JL Audio Product:
All warranty returns should be sent to JL AUDIO freight prepaid through an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt.) Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized by JL AUDIO with a valid return authorization number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Return only defective components. Non-defective items received will be returned freight-collect. Customer is responsible for shipping charges and insurance in sending the product to JL AUDIO. Freight damage on returns is not covered under warranty. Always include proof of purchase (sales receipt).
*********************************

FiX-86
Available in stores only